Winegard FV-HDCO Manuel d'utilisateur télécharger pdf

Parts List

Antenna Assembly:

Start by placing the FreeVision antenna on a at

surface so that the molded “Winegard FreeVision”

Logo on the front of the unit is facing up, Figure 1.

Lift the forward elements up until the holes in the

elements line up.

With the holes lined up, install the UHF element by

inserting the threaded posts into the holes in the

forward elements. The threaded posts should extend

down towards the body of the FreeVision antenna.

Thread the supplied nuts on the back of the threaded

posts. DO NOT tighten at this time.

Thread the coax cable through the body of the

FreeVision antenna and connect it to the matching

transformer. See Figure 2.

FreeVision Antenna

WINEGARD

FREE VIS ION

UHF Elements

Nut (2)

FIGURE 4

Matching

Transformer

w/ fork ends

Nuts

Forward

Elements

U-Bolt

Mounting

Bracket

Mounting screw

and nut

Mounting

Nut (2)

Matching

Transformer

FIGURE 3

WINEGARD

Model FV-HDCO FreeVision

™

Antenna

Ch. 7-51

FIGURE 1

WINEGARD

FREE VISION

Logo

Label

FIGURE 2

Remove and dispose of the rubber boot on the

matching transformer.

Top side of

Antenna

Coax Cable

Matching

Transformer

Forks

(Designed for use with U.S. DTV frequencies).

Made in USA

Mini Coax

Cable

Label

Pipe

Foot

(2) Bolts

(3) Nuts

(1) Carriage

Bolt

2452203 REV1

U.S. Patent D612,370 and Patent Pending

FRONT of Antenna

Point Toward Stations

For an indoor installation, use the 6’ long mini coax

cable (provided). If a longer cable is desired, you can

use or add a standard RG59/U or RG6/U coax cable

to the mini coax cable as needed by using an FS-8100

cable to cable connector.

For an outdoor installation, connect the cable that will

run from the antenna into the building.

Remove and dispose of the rubber boot on the

matching transformer before installing the matching

transformer in the body of the FreeVision antenna as

shown in Figures 2 and 3.

Once the matching transformer is installed into the

body of the FreeVision antenna, slide one of the forks

of the matching transformer between the two forward

elements on the threaded post. Repeat this process

for the other post. See Figure 4.

Tighten the nuts making sure the matching transformer

is still connected.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - WINEGARD

Parts ListAntenna Assembly:Start by placing the FreeVision antenna on a at surface so that the molded “Winegard FreeVision” Logo on the front of the

Page 2 - Mounting the antenna:

Assemble the Mounting Pipe and Foot by inserting the 2-1/2 inch screw through the pipe and foot as shown in Figure 7. Install the hex nut to hold the

Page 3 - Perpendicular

ATTACHING ANTENNA TO MAST Slide U-bolt over the pipe. See Figure 9. Point forward elements of antenna toward stations and tighten securely. Secu

Page 4 - Issue: Possible cause:

490 DAY LIMITED WARRANTY Winegard Company warrants this Winegard product against any defects in materials or workmanship within 90 (ninety) days from

Page 5

FIGURA 2Transformador adaptadorCable CoaxialListado de PiezasEmpiece por ubicar la antena FreeVission en una supercie plana de modo que el logo molde

Page 6 - Instalación de la antena:

Instalación de la antena:Selección de la Ubicación:La antena FreeVision puede usarse tanto en interiores como en el exterior. Sin embargo, es importan

Page 7 - El extremo

COLOCACION DE LA ANTENA AL MÁSTIL Resbale el sujetador en “U” sobre el tubo. Vea Figura 9. Apunte los elementos delanteros de la antena

Page 8 - Resolución de Problemas:

5GARANTÍA LIMITADA DE 90 DÍASWinegard Company garantiza que este producto Winegard está libre de cualquier defecto en los materiales o fabricación del